Other

Fit Kit SET811 contains all the parts needed to thru-axle mount an Old Man Mountain bike rack to the rear of your bike with a 12mm rear thru-axle. This kit includes: - 12 x 168—180mm thru axle with 1.75 mm thread pitch - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

Fit Kit SET702 contains all the parts needed to thru axle mount an Old Man Mountain bike rack to your fork with a 15 mm thru axle. This kit includes: - 15 x 145 mm thru axle with M14 x 1.5 mm thread pitch to fit Fox 15 x 100 mm forks (may fit others as well) - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

Fit Kit SET704 contains all the parts needed to thru axle mount an Old Man Mountain bike rack to your fork with a 15 mm thru axle. This kit includes: - 15 x 155 mm thru axle with M14 x 1.5 mm thread pitch to fit Fox Boost forks (may fit others as well) - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

Fit Kit SET701 contains all the parts needed to thru axle mount an Old Man Mountain bike rack to your fork with a 15 mm thru axle. This kit includes: - 15 x 148 mm thru axle with M15 x 1.5 mm thread pitch to fit Rock Shox forks (may fit others as well) - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

Fit Kit SET703 contains all the parts needed to thru axle mount an Old Man Mountain bike rack to your fork with a 15 mm thru axle. This kit includes: - 15 x 158mm thru axle with 15 x 1.5 mm thread pitch - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

Fit Kit SET715 contains all the parts needed to thru axle mount an Old Man Mountain bike rack to your fork with a 15 mm thru axle. This kit includes: - 15 x 198mm thru axle with 1.5 mm thread pitch - A pair of pucks - Clear protective tape - Stainless steel mounting hardware - Axle mounting increases our rack's load capacity to 70lbs/33kg - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles. Axle Length does NOT equal hub standard. This refers to the length of the axle shaft. All axles are compatible with +/- 2mm.

This pair of drop outs attach the Divide rack frames to your bike. The asymmetrical design allows for eyelet mounting or attachment to Robert Axle Project thru axles. - Made from 6061 aluminum and powder coated for durability - Adjustable height - Fits front and rear installations - Fits on all Divide and Divide Fat models - Includes hardware

This pair of 6" long extenders attaches the Old Man Mountain rack frame to the front fork. The extenders have a slot for adjustability, which allows you to level the rack on different types of bikes. Includes hardware. - 6" length - Includes slots for adjustability - Made from 6061 aluminum and powder coated matte black for finish and durability - Can be mounted to eyelets or to the Old Man Mountain pucks if your bike does not have eyelets - May need to be bent to fit width of frame - Includes hardware

This pair of 14" long extenders attaches the Old Man Mountain rack frame to the rear of your bike. The extenders have a slot for adjustability, which allows you to level the rack on different types of bikes. Includes hardware. - 14" length - Includes slots for adjustability - Made from 6061 aluminum and powder coated matte black for finish and durability - Can be mounted to eyelets or to the Old Man Mountain pucks if your bike does not have eyelets - May need to be bent to fit width of frame - Includes hardware

Need to mount a light on your Old man Mountain rack? Well you're in luck! Here's a light mount that fits clip-on lights and lights with 50mm mount spacing. - Powder-coated black, 6061 aluminum

These pucks attach the Old Man Mountain rack frame to the front or rear of your mountain or fat bike. They provide a secure upper attachment point for the rack. Included in the packet are heavy-duty zip ties, clear protective film, and mounting hardware. Designed for use with carbon, steel, titanium, and aluminum bikes and forks. Slots in the puck also allow for use with metal hose clamps (not intended for carbon bikes). Pucks can be left on the bike for future reinstallation of the rack. Recommended for use only with specific Panduit brand 120 lbs zip ties. Panduit #BT2LH-TL0. - One size fits all mountain and fat bikes - For use on either rear seatstay or front fork - Made from a carbon resin composite for lightweight strength - Includes heavy-duty zip ties with stainless steel tangs (extra zip ties included) - Includes clear protective film - Hardware included

These pucks attach the Old Man Mountain rack frame to the front or rear of your road, gravel, or cross bike. They provide a secure upper attachment point for the rack. Included in the packet are heavy-duty zip ties, clear protective film, and mounting hardware. Designed for use with carbon, steel, titanium, and aluminum bikes and forks. Slots in the puck also allow for use with metal hose clamps (not intended for carbon bikes). Pucks can be left on the bike for future reinstallation of the rack. Recommended for use only with specific Panduit brand 120 lbs zip ties. Panduit #BT2LH-TL0. - One size fits all road, gravel, or cross bikes. - For use on either rear seatstay or front fork - Made from a carbon resin composite for lightweight strength - Includes heavy-duty zip ties with stainless steel tangs (extra zip ties included) - Includes clear protective film - Hardware included

Fit Kit SETQRF contains all the parts to mount the rack to the front of a road or mountain bike with a 9 x 100mm quick-release hub. This kit includes: - 9 x 100mm QR Skewer - A pair of pucks - Clear protective tape - all mounting hardware - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles.

Fit Kit SETQRR contains all the parts to mount the rack to the rear of a road or mountain bike with a 10 x 135mm quick release hub. This kit includes: - 10 x 135mm QR Skewer - A pair of pucks - Clear protective tape - all mounting hardware - Fit Kits make it easy to swap between bikes or front and rear mounting with just a few bolts - Fit Kits protect your bike. Not all bike eyelets are meant for racks, most are only made for fenders or have very low weight limits. Axle mounting protects your frame We partner with The Robert Axle Project to supply our thru axles.

Have a current Bomber Z1 but missing that Coil Spring feel? Or, maybe you have a Bomber Z1 Coil already and want to customize its ride. Look no further. With this conversion kit, you can now convert your Bomber Z1 air fork easily to the Z1 Coil. Buy this upgrade kit and follow the install instructions (or have your bike shop swap it out for you) and you, too, will be riding the buttery-smooth Z1 Coil in no time. PLEASE NOTE: To do the conversion, you will need the Bomber Z1 Plunger & Topcap Kit.

Have a current Bomber Z1 but missing that Coil Spring feel? Or, maybe you have a Bomber Z1 Coil already and want to customize its ride. Look no further. With this conversion kit, you can now convert your Bomber Z1 air fork easily to the Z1 Coil. Buy this upgrade kit and follow the install instructions (or have your bike shop swap it out for you) and you, too, will be riding the buttery-smooth Z1 Coil in no time. NOTE: To do the conversion, you will also need to purchase the Bomber Z1 Coil Conversion Spring

Entirely developed, designed, and produced in Denmark by CeramicSpeed, the Oversized Pulley Wheel System for SRAM eTap is a huge technological advance for the cycling industry. Matching the highest quality materials with a unique design, the OSPW System delivers lower friction and longer lifetime, improving your competitive advantage. Thanks to the OSPW System for SRAM eTap, the power savings over OEM pulleys start at 40%, and the CeramicSpeed Bearings inside guarantee 3-5 times greater longevity compared to commonly used standard pulleys on the market. The watt savings with a CeramicSpeed OSPW System for SRAM eTap start at 1.6 watts. The OSPW system for SRAM eTap derailleurs is compatible with up to a 32-tooth cassette size and with both short cage & WiFli derailleur bodies. The product is for 11-speed eTap and is not compatible with 12-speed SRAM eTap AXS. If you have the updated 11-speed SRAM eTap derailleur featuring the orbit clutch, you will need the CeramicSpeed OSPW System for SRAM eTap AXS derailleurs. - The overall power savings of the OSPW System for SRAM eTap commonly reach 40%-60% over a stock setup. - The oversized pulley wheels have a lifespan that is 3-5 times longer than the commonly used standard pulleys on the market. - The OSPW system for SRAM eTap derailleurs is compatible with up to a 32-tooth cassette size and with both short cage & WiFli derailleur bodies. The product is for 11-speed eTap and is not compatible with 12 speed SRAM eTap AXS. - This 3D-printed titanium version of the OSPW System comes with our CeramicSpeed Coated Bearings for even longer service life and lower friction. In The Box: - Oversized Pulley Wheel System - CeramicSpeed Bearing Oil in 15 ml dropper bottle - Sticker sheet - IMPORTANT: When traveling, please remember to dismount your entire rear derailleur with an Allen key, as the OSPW System will not fit safely in most bike travel bags and could be damaged if left on.

This is an updated version of the 3D-Printed Ti OSPW for Shimano 9100/8000. This new design has an integrated stop tower for easier mounting. The CeramicSpeed Oversized Pulley Wheel System has been proven to be the fastest pulley system in the world, providing energy savings starting at 2.4 watts over standard Shimano systems. The OSPW System for Shimano 9100/8000 is an industry-leading product, chosen by many of the world's leading cycling teams and professional triathletes. Featuring a 13-tooth upper pulley wheel and a 19-tooth lower pulley wheel to provide absolute optimization of the rear derailleur, the upper and lower oversized aluminum pulley wheels are fitted with coated CeramicSpeed Bearings for even longer lifetime and lower friction. Please note: The 9100/8000 system is not compatible with Ultegra 8000-GS or 8050-GS (medium cage) derailleurs, nor is it compatible with clutch-equipped Ultegra RD RX800 & RX805. Please see CeramicSpeed's Shimano 11 Speed Pulley Wheels for a compatible upgrade. - The overall power savings of the OSPW System for Shimano 9100/8000 reach 30%-60%, or more in some cases, over a stock setup. - The oversized pulley wheels have 3-5 times longer lifetime than the commonly used standard pulleys on the market. - The Shimano 9100/8000 OSPW system is compatible with up to a 32-tooth cassette for both Dura Ace & Ultegra derailleurs. In The Box: - A complete 3D-printed 13-tooth/19-tooth OSPW System - CeramicSpeed Bearing Oil in 15ml dropper bottle

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 30mm - Outer Diameter: 42mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 24mm - Width: 5mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 26mm - Width: 5mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 12mm - Outer Diameter: 24mm - Width: 6mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 15mm - Outer Diameter: 28mm - Width: 7mm

All CeramicSpeed Bearings are hand-built in Denmark. Super-smooth CeramicSpeed grade 3 Silicone Nitride balls are matched (within microns) with hardened steel raceways that feature an ultra-smooth polished groove. The balls are held in place by a reinforced polyamide cage. Every bearing is optimized with a low-viscosity CeramicSpeed All Round Grease to minimize friction and increase bearing life. Non-contact seals complete the bearings, keeping dirt and moisture out. CeramicSpeed Bearings can be used for any cycling discipline: Road, TT, Tri, Track, Cross, and MTB. The benefits are super low friction, better power transfer, and increased bearing life. During the building process, we check each bearing four times by hand to ensure that all parts are matched perfectly. CeramicSpeed Balls are 400% smoother, 128% harder, and 58% lighter than standard steel bearings normally used in the bicycle industry. When comparing the CeramicSpeed Balls with other ceramic balls in the industry, you will find that the CeramicSpeed Balls are 15% harder, take 99% higher loads, and are 100% smoother. - Inner Diameter: 17mm - Outer Diameter: 30mm - Width: 7mm

Developed and designed entirely by CeramicSpeed, the Oversized Pulley Wheel System for Campagnolo is advanced for the optimization of bike performance. Everything from bearings to the cage is made from the highest quality materials. The oversized aluminum pulley wheels are fitted with standard or coated CeramicSpeed Bearings, which reduce friction to the minimum. The 13-tooth/19-tooth OSPW for Campagnolo provides 40% lower friction over a standard 11-tooth Campagnolo pulley wheel and fits up to a 32-tooth cassette. The OSPW for Campagnolo is compatible with all Campagnolo electronic rear derailleur (EPS) and all rear derailleurs with a mounting sleeve—no matter the age and model. At this point, this OSPW System is not compatible with the Campagnolo 12-speed Record and Super Record derailleurs. The OSPW for Campagnolo is compatible with: - Record mechanical - Record EPS - Super Record mechanical - Super Record EPS - Potenza mechanical - Chorus Please note, some models of Campagnolo rear derailleur, including all EPS models, do not feature a B-limit adjustment. While this product is still compatible with those derailleurs, it may not be possible to fit a 32 tooth cassette successfully on some bikes. When travelling, please remember to dismount your entire rear derailleur with an Allen key, as the OSPW System will not safely fit in most bike travel bags and could be damaged if left on. In The Box: - Oversized Pulley Wheel System - CeramicSpeed Bearing Oil in 15ml dropper bottle - Sticker sheet

Developed and designed entirely by CeramicSpeed, the Oversized Pulley Wheel (OSPW) System for Shimano 9000/6800 provides the ultimate optimization of your bicycle's drivetrain. This OSPW System features a set of 17-tooth aluminum Pulley Wheels housed in a specially designed polyamide (PA) and carbon cage. The upper and lower 17-tooth oversized aluminum pulley wheels come fitted with either standard or coated CeramicSpeed Bearings. The Oversized Pulley Wheel (OSPW) System is the product of choice by many of the world's leading cycling teams and triathletes. This specific system is compatible with Ultegra 6700/6770/6800/6870 mechanical and Di2 rear derailleurs and Dura Ace 7900/7970/9000/9070 mechanical and Di2 rear derailleurs. It is not compatible with Shimano Dura-Ace 9100/9150 and Ultegra 8000 series rear derailleurs. For those rear derailleurs you will need a OSPW System for Shimano 9100 series. The system is compatible with up to a 28-tooth cassette on most bikes, depending on derailleur hanger. The typical overall power savings of the OSPW System for Shimano 9000/6800 is 30%-60% over a stock setup, and the oversized pulley wheels have a lifespan that is 3-5 times longer than the commonly used standard pulleys on the market. In The Box: - A complete 17-tooth OSPW System - CeramicSpeed bearing oil in 15ml dropper bottle

The OSPW X for SRAM Eagle AXS features a narrow wide tooth profile to ensure durable chain retention. The 14-tooth upper and 18-tooth lower pulleys reduce chain drag, while the custom-designed carbon fiber pulley cage ensures both durability and light weight. - Pulley Wheels: CeramicSpeed 14-tooth upper and 18-tooth lower - Pulley Wheel Material: aluminum - Cage Material: Carbon-reinforced PA - Bearing Options: CeramicSpeed Standard or Coated - CeramicSpeed Grease/Oil: Pulley Oil - Compatibility: SRAM Eagle AXS (Electronic) - Compatibility Cassette: 10-52 tooth max - Spring Tension Settings: 3 - Speed: 12-speed - Discipline: Off-road and Gravity In the box: - A complete OSPW X System for SRAM Eagle AXS - CeramicSpeed Bearing Oil in a 15ml dropper bottle

The OSPW X System for Shimano XT/XTR 1x12 reduces friction by 35-40% compared to stock pulley configurations. The lightweight, custom-molded carbon fiber cage ensures durability. This design allows the use of the same length chain as stock pulleys. The 14-tooth upper and 18-tooth lower pulley profiles ensure stable chain retention while reducing drag. The OSPW X System is developed, designed, and handbuilt in Denmark—and proven globally. Only compatible with 1X specific derailleurs. - Pulley Wheels: CeramicSpeed 14-tooth upper and 18-tooth lower - Pulley Wheel Material: aluminum - Cage Material: Carbon-reinforced PA - Bearing Options: CeramicSpeed Standard or Coated - CeramicSpeed Grease/oil: CeramicSpeed Pulley Oil - Compatibility: Shimano XTR M9100-SGS, Shimano XTR M9100-GS, Shimano XT M8100-SGS and SLX M-7100 derailleurs - Cassette Compatibility: Up to a 10-51 tooth range - Spring Tension Settings: 2 spring tension settings - Speed: 12-speed - Discipline: Off-Road In the box: - Complete OSPW System for Shimano XT/XTR 1x12 - CeramicSpeed Pulley Oil, 15 ml - Sticker Sheet

Replacement Pulley Wheels for the CeramicSpeed OSPW System. Includes 2 pulley wheels. - Precision-machined aluminum pulleys - For use with CeramicSpeed's Oversized Pulley Wheel System only - Coated races increase bearing service life by increasing hardness of race and reducing corrosion - CeramicSpeed products with coated bearings include a 6-year warranty

- KlickFix bracket for use with all Basil handlebar bags requiring a KlickFix adapter - Easily & quickly removable - Suitable for handlebars measuring 22mm to 31.8mm - Made form composite materials - Adjustable angle

UFO Drip Chain Coating is a bottled product for chains that is applied in liquid form but which hardens to a 100% dry chain coating. It generates less friction than any other chain lube on the market (being out-performed only by the factory-treated UFO Racing Chain). The genius of UFO Drip Chain Coating is that it combines the convenience of a drip application with the friction-beating performance of a completely dry chain coating. So, not only does UFO Drip test faster than every other chain lubricant, it's properties actually rank it in a brand-new category: the liquid-applied but ultimately 100% dry chain coating. Another benefit of UFO Drip Chain Coating is the fact that the coating closes around the chain in a way that prevents all kinds of contamination your chain is exposed to when riding, from sticking to the chain. Therefore, make sure to clean your chain properly before applying UFO Drip, and it will then remain clean as long as you continously apply UFO Drip every 200 km as recommended. Find instructions on how to clean your chain and apply UFO Drip Chain Coating here. To learn more about the test results and how this product has been developed, please find all data at CeramicSpeed.com